Email or username:

Password:

Forgot your password?
Tube🍂Time's posts Post Back to profile
Top-level
Tube🍂Time

then you just work your way around the seam, cracking it apart.
15 Apr 2023 at 22:54 | Open on mastodon.social
124 comments
Tube🍂Time replied to Tube🍂Time

tada! looks like 18 cells total. maybe 2/3 AA sized?
15 Apr 2023 at 22:54 | Open on mastodon.social
Landy Manderson replied to Tube🍂Time

@tubetime The single strip of Scotch tape in the middle is a nice touch.

15 Apr 2023 at 22:58 | Open on mstdn.social
SLeiBt replied to Tube🍂Time

@tubetime Nice, can see 2 symetrical strings with temp sensor in the middle. Is the red wire connected to both strings in the far middle?

16 Apr 2023 at 6:05 | Open on mamot.fr
Tube🍂Time replied to SLeiBt

@SLeiBt yeah 2 parallel strings of 9 cells each

16 Apr 2023 at 12:33 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

it died again. the problem was this via. I dug out the FR4 and reconnected it to the trace on layer 2.
20 Apr 2023 at 4:23 | Open on mastodon.social
gpgekko replied to Tube🍂Time
Tube🍂Time replied to Tube🍂Time

back in business. for now anyway. 😅
21 Apr 2023 at 3:41 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

I 3D printed a new power connector. the strain relief is printed using TPU.
22 Apr 2023 at 18:23 | Open on mastodon.social
Darryl Ramm replied to Tube🍂Time

@tubetime Did you have to make your own contacts of could you reuse something else?

22 Apr 2023 at 19:17 | Open on hachyderm.io
Tube🍂Time replied to Tube🍂Time

any ideas about the type of connector the docking port uses? it's like a micro ribbon connector but with four rows instead of two rows. 240 pins total. pin pitch is 1.27mm. the only markings on the connector are "MXJ1" at one end and "52577A" at the other.
22 Apr 2023 at 19:36 | Open on mastodon.social
Mark J Koch ✅ replied to Tube🍂Time
Tube🍂Time replied to Mark J Koch ✅

@maehem yeah i sorta think its a Hirose product but it's not DXM, which has only 2 rows of contacts, not 4.

22 Apr 2023 at 19:51 | Open on mastodon.social
DrYak replied to Tube🍂Time

@tubetime and apparently that specific one is only found on 700 and 720 series.
Source: thinkwiki.org/wiki/Docking_Por

Probably this one is ISA only, whereas the following series have PCI and/or CardBus.

22 Apr 2023 at 19:58 | Open on mstdn.science
Daniele Pantaleo 🦥:verified: replied to Tube🍂Time

@tubetime looks like some kind of mezzanine connector

22 Apr 2023 at 20:31 | Open on techhub.social
Tube🍂Time replied to Tube🍂Time

i figured it out. it is the AMP .050 CHAMP line of docking connectors.
22 Apr 2023 at 23:55 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

oh i should fix the backlight, which blinks on and off for some reason. time to take it apart!
2 May 2023 at 2:15 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

welp, looks like i missed a few electrolytic capacitors. check out all that nasty corroded fuzz on the nearby component leads!
2 May 2023 at 2:16 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

all cleaned up! i had to remove all those parts, add flux and reheat all the pads, scrub with IPA, and then put everything back in place. and replace the caps, of course.
2 May 2023 at 2:17 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

it lights up and stays lit, so i'll call that a win. (yes, the hard drive still isn't working, so it's not booting.)
2 May 2023 at 2:18 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

i just got the AC adapter for this! it came in from everyone's (not) favorite auction site. the listing conveniently forgot to mention that it REEKS of cigarette smoke. 🤢
oh well, at least it was cheap.
6 May 2023 at 16:59 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

even the inside smells like smoke. it's not an ultrasonically-welded plastic case (just held together with 4 screws hidden under the labels) so it's definitely not airtight.
6 May 2023 at 17:00 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

pulled the main power transformer for reverse engineering purposes.
6 May 2023 at 17:01 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

last night i reverse engineered it. the design is simple so it wasn't too hard. the files are here: github.com/schlae/Thinkpad700C
6 May 2023 at 17:02 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

it also explains the mystery "INPUT SIGNAL" pin on the old 4-pin IBM Thinkpad power connector. this pin simply increases the output current limit when it is pulled low by the laptop. it's because the power brick is also the battery charger, and when the laptop is turned on, you have to increase the current to compensate.
6 May 2023 at 17:04 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

anyway, isopropyl alcohol wipes and a bath in Simple Green has mostly taken care of the bad smell.

6 May 2023 at 17:06 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

now for that pesky docking connector: I've discovered that a 1.2mm PCB fits perfectly in the connector, so I made a set of two boards that stack and break out all the pins to 0.1" headers.
6 May 2023 at 18:37 | Open on mastodon.social
George Laskowsky replied to Tube🍂Time

@tubetime Please don't step on those! Lego is bad enough already

6 May 2023 at 18:38 | Open on mastodon.gamedev.place
Tube🍂Time replied to Tube🍂Time
math blasterson replied to Tube🍂Time

@tubetime Haha, that was actually my first thought when you started this thread. "Those are just dressed up card-edge connectors." Nice job.

6 May 2023 at 18:48 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

now you know why I need a working logic analyzer. these pins also go to the hard disk connector inside, which makes me think they are the internal bus. the trick is to figure out what they do.
6 May 2023 at 19:43 | Open on mastodon.social
Dustin replied to Tube🍂Time

@tubetime holy smokes you are really deep-diving on this one, well done!

6 May 2023 at 19:46 | Open on geekdom.social
Tube🍂Time replied to Tube🍂Time

next step is to identify control lines vs address and data
6 May 2023 at 20:01 | Open on mastodon.social
DrYak replied to Tube🍂Time

@tubetime when you manage ti document it, you're probably going to make a few hardcore ThinkPad fan happy.

Expect retro OPL2/3 sound card and joystick ports to appear.

6 May 2023 at 20:08 | Open on mstdn.science
Tube🍂Time replied to Tube🍂Time

starting to pick out a few lines. between the cursors is an extended bus cycle
6 May 2023 at 20:39 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

now I'm writing short programs in DEBUG to help me figure out which data lines are which.
7 May 2023 at 22:01 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

i've got all the address and data lines mapped out, and all the basic control lines. now to figure out the DMA lines...
8 May 2023 at 0:09 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

and that's 99% of it figured out. i haven't untangled which IRQ is which, and there are a small number of signals i don't understand yet. but this is functional enough to start building adapters. i'll publish this at some point.
8 May 2023 at 4:56 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

there are a few signals unique to the hard drive connector, so I'm figuring those out now.
9 May 2023 at 0:55 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

the unique signals are the card setup line (turns out this is slot 1 and the dock connector is slot 2), the high address bits predecoded, IDE style, and what seems to be a system reset line.
10 May 2023 at 1:05 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

the hard disk drive has a weird 60-pin AMP CHAMP connector (5176376-2) but that just gets wired to a 52-pin 2mm header. the pin wiring is 1:1 except for the last 8 pins which are not connected.
10 May 2023 at 1:07 | Open on mastodon.social
Tube🍂Time replied to Tube🍂Time

it was surprisingly hard to figure out that AMP part number, btw. connector manufacturers constantly scrub all information about old products because who knows 🙃

10 May 2023 at 1:08 | Open on mastodon.social
Jeff Haluska replied to Tube🍂Time

@tubetime Haven't seen somebody do that in about 25 years.

8 May 2023 at 0:48 | Open on mastodon.social
Jeff Haluska replied to Tube🍂Time

@tubetime Time to invent a rubbing alcohol pressure washer.

6 May 2023 at 17:01 | Open on mastodon.social
ĸurth replied to Tube🍂Time

@tubetime don't say 'just screws' … bless the screws

6 May 2023 at 17:02 | Open on social.tchncs.de
FozzTexx replied to Tube🍂Time

@tubetime I once got something that was so bad that the things inside that were still sealed in the original shrink wrap reeked of smoke when I took the shrink wrap off. I ended up throwing away most of the items.

6 May 2023 at 17:01 | Open on mastodon.fozztexx.com
Jeff Haluska replied to Tube🍂Time

@tubetime You're taking good care of the capacitors they're growing in size! 😆

2 May 2023 at 2:19 | Open on mastodon.social
Joe Pasqua replied to Tube🍂Time

@tubetime Now that would be a truly useful AI - upload a picture of a connector (perhaps with a ruler for scale), and it tells you what the connector is and where to get it.

Yours was a tough one, but its hard even for more common connectors. Next time I go to Anchor I’m going to take some stuff with me to see if I can find matching connectors.

23 Apr 2023 at 1:24 | Open on mastodon.social
Go Up