|
Top-level
I was looking back at this idea of converting an ATmega328 into a pluggable module via an IDE 40 pin connector. It occurs to me that, most of the time, you would program a chip, drop it into a project box, and that's about it Which means, it's really not necessary to have every analog and PWM pin connected at all times, just ones you're using (usually 5-6 at most in my case). And it's safer and simpler to have as few intrusions as possible into your enclosure for waterproofing too 22 comments
There's also the issue of project boxes. Generally, these are injection moulded ABS plastic and come in small sizes with screws and such. Some are weather "resistant". The cheaper ones are almost always only for keeping out humidity, not being submerged or sprayed with water Which makes me wonder whether I actually need a project box, or just a small diameter PVC pipe. Only one end needs to be sealed while the "wire end" can be pressure fit with a bit of silicone around the holes in the cap This is an excellent video on building a power supply for hobby projects (Arduinos etc...) I'll likely be using an onboard circuit delivering 12V, 5V, and 3.3V, which can run off a battery or solar panel so I don't have worry about multiple power supplies for the ATmega328 and other peripherals Most of my projects probably won't be directly connected to mains power anyway Maybe I can build a pluggable power supply module for that as well While looking at a suitable chip to control my switching power supply for the ATmega328, I came across this calculator for the MC34063A http://www.nomad.ee/micros/mc34063a/ The 34063 is pretty much the 2N2222 of the DC/DC converter world. If you got a generic converter or one of those car charger adapter thingies, chances are it's powered by one of these chips. So it's good to have a good calculator to go with with the settings you need I just had a terrible idea that, much to my relief, others have already tried out. I couldn't find any instances of house fires or serious injuries related to this so I'll take that as a good sign Using an old fashioned 555 timer as the pulse trigger for a switched mode power supply In fact, here's a pretty nice project on using the 555 timer as a variable power supply for a nixie tube https://github.com/tardate/LittleArduinoProjects/blob/master/Electronics101/555Timer/NixiePowerSupply/README.md A lot of Arduino projects use the 7805 voltage regulator, but if I'm only powering the ATmega328 chip and nothing else (not even the LED or optocouplers), I think I can get away with using a 78L05 16MHz+ speed is supported between 4.5V - 5.5V, but (according to the datasheet) running on the internal 8MHz clock should only draw 2.7mA Including the external 16MHz crystal, it may be 80mA+ total (30ohm ESR crystal, 2 - 22pf caps, and 10K resistor) 78L05 can support up to 100mA so it's just enough It's oddly liberating to design a circuit schematic in Notepad Next challenge is making all that fit into this 3x7cm perf board I'm not too worried about power dissipation just yet, but I'm going to try and orient all the MOSFETs to one side so their heatsinks away from the rest of the board I'm half tempted to try and squeeze a different version into this 2x8cm board as a fun challenge, but that may be for later Actually, I got this board to try out a minimal ATmega328 setup with just the crystal, resistor and the 2 capacitors Added a project page for the power supply. Just a place to put down ideas while I sketch them https://github.com/cypnk/Cabin-Life/tree/master/Power%20Supply I'm always uncomfortable when adding disclaimers to anything I.E. "Not responsible for sparks, fires, or worse, by using my poorly thought out ideas in this thing thing I wrote at 9AM on a Sunday while running low on coffee" OK I think we can call it a day This *shouldn't* immediately blow up after connecting power This was a challenge and a half without a working oscilloscope. I really can't afford a new one right now so a lot of the component values are blank (or wrong) for now (Stream of consciousness hardware hacking is a bad idea, kids. Don't try it at home) I'm still liking the Notepad schematic idea since I can freehand pretty much everything and it's not going to complain NASA's Through hole soldering guidelines might come in handy when it's time to assemble components for my power supply If I'm building it to function way off in the woods, exposed to all manner of whatnot, soldering is probably the least of my worries. But why allow the possibility for small issues to accumulate into big problems https://workmanship.nasa.gov/lib/insp/2%20books/links/sections/601%20General%20Requirements.html  @cypnk omg I love that these workmanship standards are just out there to read  @darius @cypnk as i remember, this discussion came up at sparkfun when we realized that people were *actually* sending our stuff to space on cubesats and the like. which is definitely, like, a holy shit cool moment, and then a lot like when you find out people are using it for medical devices you go wait, are you sure you want to do that, because i probably wouldn't do that |
Gregory's Server
This makes me wonder if good old fashion automotive connectors with 4-6 pins (and maybe another pair with an inline fuse for power) are all that's needed. They're certainly a lot simpler than having to solder 40 pins
I was thinking of creating an ESD and over/under volt protected circuit to power an ATmega328 chip with opto-isolated data pins
Something like a dongle that I can quickly plug into my projects around the place